Hitch rack swing adapter. Now you can rack up the bikes and still access your tailgate. The BackSwing hitch adapter turns your hitch product into an easy-to-use swing-away rack that locks up tight while you're on the road. It works seamlessly with most 2" bike racks, like the HoldUp EVO - as well as almost any other rack using a 2" receiver - to let you swing your fully loaded rack out of the way so you can easily get to your coolers, gear, and Fido. Product Details: - Hitch extension converts most 2" hitch products to a swing-away rack - Provides easy tailgate access - even with a rack fully loaded with bikes - Easily swings open 90 degrees and locks in place with the simple to use release lever - Safety latch secures the rack closed while you're on the road - Secures to any 2" hitch receiver using a threaded pin - Included SKS (Same Key System) lock keeps the rack secure - 250 lb maximum load capacity (rack plus gear) Product Specs: - Weight: 35.46 lbs - Dimensions: L 20.00" x W 30.00" x H 8.00" Installation Details: - Some Assembly Required - 10 Minute Install - 2" Hitch Receiver Required Compatible with the following: - Dr.Tray- 2" only (without the EZ+1 attached) - SingleSpeed - HangOver 4 - 4 Bike only - TwoTimer - HoldUp EVO - HoldUp EVO +2 - HoldUp - HoldUp +2 - FourTimer - LongHaul (Vans and Passenger Vehicles Only) - RoadTrip (Vans and Passenger Vehicles Only)
Tailor your towers—these super-strong clips come in a wide range of sizes and designs so you can precisely fit your BaseLine Towers to your car’s bare roof.
Make carrying your boat highway safe with these bow/stern tie downs. Forget about tying knots, these tie downs feature handy ratchet pulleys that are easy to use and are corrosion resistant. They're also great for securing non-nautical loads like ladders or lumber. - Secures the bow and stern of any boat - Best in class corrosion resistance - Clear plastic tubes protect your vehicle from damage
Yakima's Chain Straps are replacement bike holding straps for various models of Yakima's trunk and hitch racks. The stretchy, sturdy rubber is easy on your bike's finish and is extremely durable for long life.
The control key is "uncut" and is used only for the removal and installation of an unlocked SKS core. Product Specs: - Weight: 0.02 lbs. - Limited Lifetime Warranty
Whether you're tinkering on your gear, prepping a meal for your crew, or mixing drinks for a night of fun, the EXO BackDeck is the perfect solution, turning your EXO system from gear hauler to working surface to bar top in seconds. When you're done, simply stow it and get back on the road. - Connects to the EXO SwingBase or EXO TopShelf in seconds using the EXO cleat system - 50" x 17" UV protected bamboo work surface - Tool-free, locking SpeedKnobs attach and lock EXO BackDeck to EXO SwingBase or EXO TopShelf - Included bag protects the tabletop when not in use and makes for easy transport - Sized to store inside the EXO GearLocker or EXO GearWarrior - 80lb weight capacity - 1 Year Warranty - Not intended to be used as a cutting surface - Requires EXO SwingBase and/or EXO TopShelf Product Specs: - Weight: 10.80 lbs. - Dimensions: L 17.00 in x W 50.50 in x H 0.75 in - Limited One Year Warranty
Make the most of your EXO GearLocker with the EXO GearTotes, collapsible, dividable totes that make it easy to stay organized from house to vehicle to destination and back again. A durable ripstop nylon build, and 50-pound carrying capacity make these perfect for everything from groceries to gear. - Heavy-duty totes carry up to 50 lbs. of gear each - Perfectly sized for the EXO GearLocker - Totes fold flat for easy storage when not in use - Includes a removable divider with hook-and-loop attachment - Structural webbing handles make it easy to haul loaded totes to your vehicle or campsite - Made of 600D fabric with durable PU Coating - Each tote measures 13" x 17.5" x 9" - Sold as a 2-Pack - 1 Year Warranty Product Specs: - Weight: 4.09 lbs. - Dimensions: L 18.00 in x W 13.50 in x H 9.50 in - Limited One Year Warranty
Organize and stow your camp kitchen gear with this all-in-one system, simplifying your effort so it’s always ready to grab-and-go. The rugged, road-worthy box can seamlessly attach to the EXO System for smooth transport to your campsite, trailhead, or ball game. Open it up and turn it into a fully functional work station, making it easy to prep, cook, and serve from the same spot. The system can also be expanded with side-mounted tables and a free-standing Leg kit to grow and customize your EXO OpenRange as needed. PRODUCT DETAILS - Connects to the EXO SwingBase or EXO TopShelf in seconds using the included EXO cleat system - Durable rotomolded enclosure with a rubber door seal keeps your gear fully protected from weather, dust, and critters - Fold down front door allows easy access to your gear and can be used as a prep surface - Internal shelf and integrated utensil drawer help to organize your cooking and camp gear - 85 liters (90 quarts) of internal storage space - Includes SKS locking latches to secure your gear - Tool-free, locking SpeedKnobs attach and lock EXO OpenRange to EXO SwingBase or EXO TopShelf - Includes a lantern hook, backboard organizer and handheld bottle opener - Full suite of accessories available to expand your EXO OpenRange - EXO SwingBase and EXO TopShelf recommended but not required for transport - Made in the USA PRODUCT SPECS - Weight: 37.00 lbs. - Dimensions: L 31.00 in x W 18.00 in x H 18.00 in - Limited Lifetime Warranty
Getting pressurized water to your destination just got even easier. The EXO RoadShower Kit lets you attach the RoadShower 4G and 7G to your EXO system giving you more mounting options for your RoadShower. Product Details - Connects RoadShower 4G and 7G to the EXO SwingBase or EXO TopShelf in seconds using the EXO cleat system - Tool-free, locking SpeedKnobs attach and lock RoadShower 4G and 7G to EXO SwingBase or EXO TopShelf - Heavy-duty steel construction with durable, powder-coated finish - Includes all mounting hardware (EXO System and RoadShower are sold separately) - Not compatible with RoadShower 10G Product Specs - Weight: 2.46 lbs. - Dimensions: L 14.00 in x W 3.00 in x H 4.00 in
We made hauling from home to vehicle to anywhere a snap with the EXO WarriorWheels—wheels and a handle that connect to your EXO GearWarrior, even while it's still on your hitch. Simply snap it together and wheel your gear to wherever you're headed next, whether it's basecamp, the beach or the marina. - Connects to the EXO GearWarrior (or other Warrior baskets) in minutes without tools - All-terrain tires maneuver well over all types of surfaces and handle curbs and roots with ease - Roll up to 110 lbs. of gear to your camp or soccer practice - Large easy to grab handle is positioned to allow for maximum control when going downhill - 2 Year Warranty - Not intended to remain installed during vehicle transport Product Specs: - Weight: 18.50 lbs. - Dimensions: L 64.00 in x W 21.00 in x H 39.00 in - Limited Two Year Warranty
- Fits all Yakima crossbars except 86-inch - Sold in sets of 4
Getting your gear onto your rack isn't complete until you've secured it. This pair of super strong box-stitched 16" straps include soft, rubber-coated buckles to protect your boats and gear from scratches.
Pair of EndCaps for Yakima JetStream bars.
Custom Landing Pads to install directly to the factory fixed mounting points of the 2005+ Toyota Tacoma. Combine with SkyLine Towers and StreamLine crossbars for a full-featured Yakima base rack, significantly increasing cargo capacity over the factory crossbars. Product Details - Includes a snap-on cover when not in use - Each pad sold in a set of two - Includes 4 metal "C" anchor plates 1-3/16" x 13/16" and 4 metal "D" anchor plates 1-1/2" x 13/16" (Contact Yakima Customer Service for additional size anchor plates) Product Specs - Weight: 0.86 lbs. - Limited Lifetime Warranty
Landing Pad designed to fit a variety of BMW vehicles with fixed 7mm threaded mounting points. Combine with SkyLine Towers and StreamLine crossbars for a full-featured Yakima base rack, significantly increasing cargo capacity over the factory crossbars. Product Details - Includes a snap-on cover when not in use - Each pad sold in a set of two - Includes 4 metal "C" anchor plates 1-3/16" x 13/16" and 4 metal "D" anchor plates 1-1/2" x 13/16" (Contact Yakima Customer Service for additional size anchor plates) Product Specs - Weight: 0.86 lbs. - Limited Lifetime Warranty
Expand the cooking surface on your EXO OpenRange with this metal side table. PRODUCT DETAILS - 16" x 31" Powder coated steel surface is heat resistant and perfect for stove use - Height adjustable support leg (26-44"), to level out the table - Metal rod folds out to support camp stove propane tanks, or doubles as a towel rack - Included storage bag helps protects the side table for in-vehicle storage PRODUCT SPECS - Weight: 13.50 lbs. - Dimensions: L 31.00 in x W 16.00 in x H 0.50 in - Limited Two Year Warranty
Expand the food prep zone on your EXO OpenRange with this bamboo wood side table and nesting cutting board. PRODUCT DETAILS - 13" x 27" UV protected Bamboo table with a premium finish - Height-adjustable support leg (26-44"), to level out the table - Includes plastic cutting board and collapsible wash basin with drain hose that nests into the table surface cutout - Included storage bag protects the side table when not in use and can be stowed inside OpenRange PRODUCT SPECS - Weight: 5.50 lbs. - Dimensions: L 27.00 in x W 13.00 in x H 0.50 in - Limited Two Year Warranty
Tailored to precisely fit flush-mount factory side rails, RidgeClips secure the RidgeLine Towers to your aerodynamic rooftop. Created in different designs to fit specific vehicles, they have a brilliant clip design that’s super strong, easy to install, and holds on tight. - Ingenious clips designed to attach RidgeLine Towers to flush-mount factory side rails - Range of shapes lets you find the precise, secure fit specific to your vehicle - Unique inner and outer clip design delivers exceptional hold - Powder-coated stainless steel provides maximum strength and durability - Sold in sets of four – just one kit sets up your system
With more than a quarter century of real-world testing, Yakima's iconic round bar is proven across a range of adventures and under a variety of loads. Strong, utilitarian and easy to use—this classic is a classic for a reason. Bar adapter that allows you to run RoundBar on StreamLine Towers. - Adapter required to use RoundBars with the New StreamLine Towers. Sold in a set of four. - Includes 4 RoundBar end caps Product Specs: - Weight: 0.42 lbs. - Dimensions: L 2.00 in x W 2.00 in x H 1.00 in - Limited Lifetime Warranty
SafetyMate ensures you are street-legal when using the StageTwo and StageTwo +2. Keep the clean lines and style of the StageTwo family going with the clean LED Lightbar and internal electrical routing. Safety never looked so good. PRODUCT DETAILS - Keeps your lights and license plate visible while on the road? - Attachment points allow SafetyMate to be visible while StageTwo is in use as well as folded up - Powerful LED taillights have full brake, turn signal, and lighting functionality - Flexible license plate attachment helps protect your plate from steep driveways - Fits all US and Canada plates - Wiring is internally routed through StageTwo and StageTwo +2 for a clean look - Uses 4-Flat electrical connection and includes all necessary wiring to connect to your vehicle's wiring harness - Compatible with StageTwo and StageTwo +2
Yakima's Side Loader Brackets are permanently side-mounted brackets that fit in the space between the top of your truck and the side window. They allow Yakima 1A Raingutter Towers to be used in some situations where no rain gutters exist (towers sold separately).
Take your HighSpeed or HighRoad bike mount to the next level with the SmarT-Slot Kit 1.This hardware kit replaces the standard mounting hardware to enable direct attachment of your bike mount into a T-slot channel on your crossbar. It works with Yakima JetStream crossbars as well as most other T-slot crossbars on the market. - Includes T-slot hardware, covers, and install tool. - Designed to work exclusively with Yakima HighSpeed and HighRoad bike mounts. - Compatible with Yakima JetStream bars and most other T-slot style crossbars. Product Specs: - Weight: 0.25 lbs. - Dimensions: L 2.75 in x W 1.50 in x H 0.50 in - Limited Lifetime Warranty
Go super sleek with this low-profile conversion kit that lets you mount your FatCat or FatCat EVO to T-slotted crossbars, such as Yakima's JetStream bars. PRODUCT DETAILS - Custom-designed for Yakima FatCat and FatCat EVO snowsports mounts - Quick and easy installation - Includes slide in T-bolts and low-profile spacers - Works with our JetStream bars, FlushBar, RailBar, and most other t-slot style crossbars TECHNICAL SPECS - Weight: 0.30 lbs - Dimensions: L 0.75in x W 0.75in x H 2.00in
Thru-axle adapter works with WheelHouse to hold wheels with 12mm and 15mm thru-axle. - Easy cam lever for quick installation - Durable stainless steel skewer - Up to 110mm front hubs Product Specs: - Weight: 0.44 lbs. - Dimensions: L 9.00 in x W 0.75 in x H 2.00 in - Limited Lifetime Warranty
Yakima's Trunk-Mount Security Strap is a steel-reinforced strap that lets you secure your trunk rack to your vehicle.
Yakima's TubeTop solves the dilemma of how to carry bikes that have frames with non-traditional top tubes, such as certain suspension bikes, women's frames, children's bikes and more. The fully adjustable TubeTop is attached to the bike to act as a frame top tube so the bike will mount on all Yakima rear racks. Plus, the TubeTop's large molded collars are gentle on stems and seatposts. This Item may be in stock with Black accents or with Red, but both use the same part numbers. Please contact us to confirm the color of product in stock.
A straight-forward, easy-to-use, locking QR skewer that fits any fork-style bike mount on the market. Compatible with any 9mm x 100mm axles. - Durable stainless steel axle and body - Easy-to-adjust end nut and cam lever - Lockable with SKS lock, sold separately
Rubber straps used to secure bikes to Yakima hitch and strap racks manufactured prior to 2004. Each strap has 5 holes which are 3/4" in diameter. Since 2004 we have used rubber straps called Chain Straps, which each have 8 holes that are 1/2" in diameter.
The Thule Xadapt 8 Adapter Kit makes it possible to connect Thule carriers to Thule Professional load bars. Please contact us with any questions regarding compatibility.
The Thule Xadapt 9 Adapter Kit makes it possible to connect Thule carriers to Thule Rapid Aero and Thule Professional load bars. Please contact us with any questions regarding compatibility.
Page 1 of 4 Next page